My main source today is H. Stopes, author of the classic "Malt and Malting", published in 1885.
"The Manufacture Of Black, Amber, Crystal, And Other Special Malts.Hitherto we have been considering one class of malt only, viz. that technically known as pale malt. Several other varieties exist. Under this heading we shall consider those only which depend upon the conditions already explained, but with a variation of the final process of drying, such variation being chiefly a comparatively slight difference of temperature.What interests me about this passage is Stopes' dismissal of adding wood to increase the temperature of the kiln as an absurd and expensive practice that was disappearing. Though, it seems as if the practice survived into the lat 20th century. This is what Guy Horlock of French & Jupps has to say about making brown malt:
Amber, porter, blown, or imperial malt can be made in any ordinary malting, the
differences to which they owe their names being almost entirely effected upon
the kiln. The scope they afford to the engineer for employment or improvement is
infinitesimal. They deserve mention only for the impressive fact, that the difference in temperature which will convert pale malt into amber or imperial is actually less than is to be found in the vast majority of kilns, between the temperature of that pale malt lying upon the surface of the tiles or wire, and of the upper surface exposed to the air. There is probably no kiln in Great Britain having only a single floor in which this difference is less than 50°. Pale malt next the tiles will be at 200° Fahr., and upon the surface 150° or less; and malt heated to 240° would make amber or imperial malt.
Blown or porter malt has the further difference that considerable heat is applied with suddenness before it has become dried. It is well known that any given temperature over 100° Fahr. will give much more colour to malt if still moist than a much greater heat if dry. Blown malt is exposed to the flare of fast-burning oak faggots or billet wood, and gains much colour and increase of size in consequence. Its use is an absurdity that is dying out, for the colour and flavour so gained are found to be very costly.
Crystal malt is green malt not fully grown, taken straight from the floor, and placed in a woven wire cylinder over a fire, and rotated. The curious sweetness of crystal malt to the palate may be readily accounted for by the mode of its drying. Sufficient
moisture is present at considerable temperature to enable the diastase to convert a portion of the starch into sugar.
Black or patent malt is pale or other malt dried in the ordinary way, and then placed in a cylinder over a fire, and rotated. The starch and saccharine constituents are speedily caramelised, and a splendid deep colour is obtained, which is communicated to porter and stout. The chief difference in the appliances used in the manufacture
of these (crystal and black) malts is the construction of the furnaces and cylinders. They have to be made in such a manner that free inspection of the malt can take place during roasting. They must also admit of ready lateral movement to facilitate filling and emptying; and appliances for proper cooling are of importance."
"The Engineering of Malting" by H. Stopes, 1885 an article in "Transactions" journal of the Society of Engineers.
"We produced Brown Malt until 1980, but due to the dangerous nature of theSo it looks like the archaic practice of finishing roasted malts with faggots of wood didn't die out as Stopes expected. Anyone have any idea how they make brown malt nowadays?
manufacture, nobody would insure us after that date. I have been working for F&J since 1949 and I was involved quite heavily in the production of Brown Malt."
"All my period with the production, we have never used anything other than Hornbeam, both poles and faggots and I know that Taylors at Sawbridgeworth (later to become part of ABM) did the same. However I know that Swonnels at Yarmouth did use offcuts of Oak, simply because they has a woodyard (Jewsons) next door, but I have never heard of anything else in the production and never coal."
Extract from a letter written by Guy Horlock, curator, French & Jupps Museum, Stanstead Abbotts, Hertfordshire.
French (presumably short for French & Jupp) and Taylor are names that frequently crop up in the brewing logs of Whitbread and other London breweries. Usually it was either brown or black malt that they supplied.
D E Briggs in "Malts and Malting", 1998 says:
ReplyDelete"The nearest modern equivalents to porter malts are brown or drum-brown malts. They lack any wood-smoke flavour and are not snapped or blown. The brown malts are prepared from green malts or pale malts in roasting drums using direct heating, so evaporation is not limited. Temperatures are gradually increased to about 130C (266F) These brown malts are used in some specialist bottled beers, brown ales, and sweet stouts. They have a dryer, less sweet character than crystal malts, having the same colours, which are in the range 90-189 EBC units, most being about 130 EBC units. These malts have extracts of 265-275 LDK and moisture contents below 3.5%."
So quite different to blown malt then, I would think.
Some of the older (18C) brewing texts do suggest, in some instances at least, that amber and brown malts were just pale malt that had been kept on the kiln for longer. They would be smokier than pale malt only because of the increased time of kilning and were not blown. Blowing brown malt only seems to have been mentioned in later texts (19C). This may have been a development of malting techniques although there was also a lot of regional variation of methods used. Which is why Hertfordshire is particularly associated with brown malts, I guess.
I am at work, not in my book-lined study, so I can't check the references at the moment.
Kristen: some more extraneous U's for you to cope with! :-)
I've seen references to blown malt in 18th century books, usually not very coplimentary.
ReplyDeleteThe impression I get is that the method of manufacturing brown malt has had some major changes over the past 300 years. The 18th century version was used as a base malt, something that you couldn't do with the modern version without adding enzymes.
Hertfordshire was the main supplier of malt for London. Which may be why they made so much brown malt there.
"I've seen references to blown malt in 18th century books, usually not very coplimentary."
ReplyDeleteand
"The 18th century version was used as a base malt, something that you couldn't do with the modern version without adding enzymes."
Perhaps they go together: if you want brown malt as a base malt you couldn't use blown malt because of the lack of enzymes. So brewers would be very unimpressed with such malt. Perhaps maltsters producing blown malt in 18C were not very good maltsters and their poor quality blown malt was a reflection of this.
"The impression I get is that the method of manufacturing brown malt has had some major changes over the past 300 years."
I am sure you are on the money there. It's just hard to find much contempory information about the malting process.
"Hertfordshire was the main supplier of malt for London. Which may be why they made so much brown malt there."
Great communication down the Lea Valley! But this could be a chicken-and-egg argument, I suppose. Were the maltsters making brown malt because the brewers asked for it OR were the brewers using it because there was a plentiful supply to hand?